Search the repository

A+ | A- | | SLO | ENG

Abstract: This study investigates the thermal behaviour of two opaque and one transparent thin intumescent coating at material level (coating only) and system level (coating applied at real scale on timber), and their effects on timber in fire. Micro-scale tests were conducted to examine the underlying mechanisms of intumescence and degradation for each coating individually, while bench-scale tests demonstrated how these behaviours translate to larger scales. Critical temperature and heat flux thresholds were identified at which the coatings begin to insulate the timber through the formation of the intumescent char layer, as well as those marking degradation of the layer and the reduction of its insulating efficacy. The findings highlight that coating type and thickness, heating conditions and exposure duration influence mass retention, swelling pattern, and the integrity of the intumescent char layer. Overall, the transparent coating exhibited lower durability than the opaque ones. It was also shown that, due to the similar temperature ranges of timber pyrolysis and coating swelling, timber degradation occurs close to the coated surface during the transient swelling process, resulting in a heated region of 15- 20 mm with negligible mechanical properties by the end of swelling. Therefore, intumescent coatings provide insulation progressively rather than immediately.
Keywords: mass timber, thin intumescent coatings, swelling, fire testing, charring, fire safety
Published in DiRROS: 08.04.2026; Views: 140; Downloads: 117
Full text (8,52 MB)
This document has many files! More...

Abstract: In recent years, many genes have been associated with male infertility; however, testing of monogenic forms has not yet been clinically implemented in the diagnosis of severe forms of idiopathic male infertility, as the diagnostic utility has not been established yet. The aim of this study was therefore to answer if the implementation of genetic testing for monogenic forms of male infertility could contribute to the clinical diagnosis of men with severe forms of idiopathic male infertility. Materials and Methods: Based on the ClinGene curation protocol, we defined a panel of genes with sufficient evidence for the involvement with severe male infertility. We tested the 21-gene panel in a representative multicentric cohort of men with significantly impaired spermatogenesis. We performed whole exome sequencing on 191 infertile men with severe forms of idiopathic male infertility; non-obstructive azoospermia, and severe oligozoospermia (<5 million spermatozoa/mL). The control group consisted of 216 men who fathered a child. DNA was prepared based on the Twist CORE exome protocol and sequenced on the Illumina NovaSeq 6000 platform. Variants were classified using the Association for Clinical Genomic Science (ACGS) Best Practice Guidelines for Variant Classification in Rare Disease 2020. Results: We identified potential monogenic disease-causing variants in four infertile men. Pathogenic/likely pathogenic variants in STAG3 (c.2776C>T, p.Arg926*; c.2817delG, p.Leu940fs), MSH4 (c.1392delG, p.Ile465fs; c.2261C>T, p.Ser754Leu), TEX15 (c.6848_6849delGA, p.Arg2283fs; c.6271dupA, p.Arg2091fs), and TEX14 (c.1021C>T, p.Arg341*) genes were found. Conclusions: In the present multicentric cohort study, a monogenic cause in 2.1% of infertile men was identified. These findings confirm the utility of monogenic testing and suggest the clinical use of monogenic testing for men with severe forms of idiopathic male infertility.
Keywords: azoospermia, genetic testing, male, meiosis
Published in DiRROS: 18.03.2026; Views: 292; Downloads: 176
Full text (517,03 KB)
This document has many files! More...

Abstract: The qualification of in-vessel components for a fusion power plant requires a test environment with a high flux of 14 MeV neutrons over a sufficiently large surface and volume. Performance testing and qualification of the complex design and technologies of fusion nuclear components is needed, in particular that of the tritium breeding blanket (BB). Testing in relevant conditions over a relevant time will also allow gaining the necessary confidence regarding the build-up and control of tritium inventories inside the BB, which will be an important radioactive source. An option of such a volumetric neutron source (VNS) is a beam-driven tokamak. A feasibility study of the main machine components and associated plant systems is described in this article. The machine has a major radius of 2.53 m, a single-null divertor configuration, and four tangential 120 keV beamlines that generate a fusion power of approximately 30 MW and provide current drive for a steady-state plasma scenario. The plasma is small with a minor radius of a = 0.55 m to maximize the neutron wall load, up to 0.5 MW/m², similar to what is targeted in ITER. Approximately 25 m² are available for blanket testing including 4 port plugs, which offer flexibility regarding the test module operating conditions and the implementation of instrumentation. Given the small plasma, much of the tokamak's volume is made up by the neutron shielding structures that are similarly sized as in ITER. To reduce the construction risk, ITER-like concepts were adopted for many components. In some cases, however, lessons learned from ITER led to the development of customized or innovative concepts. Due to the modest fusion power the plasma will burn <1 kg of tritium per year, which can be provided from external sources.
Keywords: fusion reactors, volumetric neutron source, breeding blanket testing, tokamak, remote maintenance
Published in DiRROS: 27.02.2026; Views: 359; Downloads: 199
Full text (5,09 MB)
This document has many files! More...

Abstract: Biofouling on ship hulls significantly increases hydrodynamic drag, fuel consumption, and greenhouse gas emissions, while also facilitating the spread of invasive species in regional and global waters, thereby threatening marine biodiversity. To address these environmental and economic issues, we developed an innovative robotic platform for in-water hull cleaning. The platform utilizes a cavitation-based cleaning module that removes biofouling while minimizing hull surface damage and preventing the spread of detached particles into the marine environment. This paper describes the design, operation, and testing of a developed robotic cleaning system prototype. Emphasis is placed on integrating components and sensors for continuous monitoring of key seawater parameters (temperature, salinity, turbidity, dissolved oxygen, chlorophyll-a, etc.) before, during, and after underwater cleaning. Results from real-sea trials show the platform’s effectiveness in removing biofouling and its minimal environmental impact, confirming its potential as a sustainable solution for in-water hull cleaning.
Keywords: biofouling, ship hulls, in-water cleaning, undewater robot, sensor integration, field testing
Published in DiRROS: 27.01.2026; Views: 378; Downloads: 449
Full text (2,38 MB)
This document has many files! More...

Abstract: This paper presents key results on the laboratory testing of old girders removed from a flood-damaged bridge located near Ljubljana, Slovenia. The structure was widened in 1989 to accommodate pedestrians and cyclists by integrating prefabricated prestressed reinforced concrete T-girders. To assess the structural behaviour of the bridge, six girders were subjected to a rigorous testing program involving bending and shear tests in a laboratory setting. The tests were performed on girders with static lengths of 12.20 meters and 9.90 meters. The program aimed to evaluate the structural performance of the girders. Preliminary results indicate satisfactory structural behaviour of the prestressed T-girders under the applied loads, with insights into their performance under both bending and shear stresses. This study contributes valuable data for assessing the long-term behaviour of bridges. The outcomes are particularly relevant for optimising resource allocation in bridge rehabilitation projects and ensuring safety and functionality in transportation networks.
Keywords: laboratory testing, prestressed girders, assessment, load test, operational modal analysis, damage, acoustic emission
Published in DiRROS: 22.01.2026; Views: 373; Downloads: 231
Full text (15,91 MB)
This document has many files! More...