Digital repository of Slovenian research organisations

Search the repository
A+ | A- | Help | SLO | ENG

Query: search in
search in
search in
search in

Options:
  Reset


Query: "keywords" (drying) .

1 - 4 / 4
First pagePrevious page1Next pageLast page
1.
Influence of curing / drying methods including microwave heating on alkali activation of waste casting cores
Barbara Horvat, Vilma Ducman, 2021, published scientific conference contribution

Abstract: Within previous investigation alkali activation of waste casting cores at room temperature did not give promising results, i.e. when the precursor was gently ground and sieved below 600 %m the alkali activated material fell apart at demolding, and when the precursor was ground below 90 %m, the alkali activated material did not solidify in more than 2 years. , Therefore different drying/curing methods were applied to enhance the reaction. Waste casting cores were prepared in two granulations (sieved below 600 %m and below 90 %m), activated with Na -water glass and 10 M NaOH, cured at different temperatures (70 °C and room temperature), and subsequently cured/dried at three different conditions: room temperature, 110 °C, and irradiated with microwaves. The highest compressive strength, 25 MPa, was gained with subsequent curing/drying at 110 °C. The lowest density, 0.5 kg/l, with compressive strength above 3 MPa, was achieved with subsequent curing/drying with microwaves .
Keywords: waste casting cores, alkali activation, curing, drying, microwaves, mechanical strength
Published in DiRROS: 22.01.2024; Views: 168; Downloads: 89
.pdf Full text (9,29 MB)
This document has many files! More...

2.
The deformation of alkali-activated materials at an early age under different curing conditions
Mark Češnovar, Katja Traven, Vilma Ducman, 2021, original scientific article

Abstract: The production of alkali-activated materials (AAMs) is known for its environmentally friendly processing method, where several amorphous-rich aluminosilicate material sources combine with an alkali media solution to form solid, ceramic-like materials. In terms of the Si:Al, Na(K):Al, and Na(K):H2O ratios, the theory of AAM formation is quite well developed, but some open questions in the technology process remain, especially with regards to the means of curing, where the generation of defects can be persistent. Knowing that deformation is extremely high in the early ages, this study investigates the effects of temperature and moisture on shrinkage behavior within the first 72 h of AA pastes made from ladle (LS) and electric arc furnace (EAF) slag and activated by sodium silicate (Na2SiO3). The method to determine the deformation of alkali-activated slag-based materials, in terms of both autogenous and drying shrinkage, was based on the modified ASTM C1698-19 standard for the measurement of autogenous shrinkage in cement pastes. Autogenous deformation and strain were measured in four samples, using the standard procedure at room temperature, 40 and 60°C. Furthermore, using an adjusted method, nine samples were characterized for strain and partial surface pressure, while drying at room temperature, 40, or 60°C at a relative humidity of 30 or 90%. The results show that the highest rate of autogenous shrinkage occurred at a temperature of 60°C, followed by drying shrinkage at 60°C and 30% relative humidity, owing to the fact that the rate of evaporation was highest at this moisture content. The study aimed to provide guidance regarding selection of the optimal curing set in order to minimize deformations in slag-based alkali-activated materials. In the present case, curing at a temperature of around 40°C under lower moisture conditions for the first 24 h provided optimal mechanical properties for the slags investigated. The methodology might also be of use for other aluminosilicate sources such as metakaolin, fly ash, and mineral wool–based alkali-activated materials.
Keywords: alkali-activated materials, slag, drying, autogenous shrinkage, partial surface pressure, curing deformation
Published in DiRROS: 03.07.2023; Views: 362; Downloads: 128
.pdf Full text (2,23 MB)
This document has many files! More...

3.
Changes of ashwood pH-value during conventional drying
Aleš Straže, Sandi Torkar, Vesna Tišler, Željko Gorišek, 2003, original scientific article

Abstract: Changes of pH of sawn wood during conventional drying were studied. Green ashwood boards (Fraxinus excelsior L.), 25.4 mm in thickness, were exposed to 1 month air drying and to kiln drying using 7 schedules, reached by varying temperature (20°C, 30°C and 65°C) and relative air humidity (33% to 90%). Wood samples for pH and moisture content (MC) determination were taken in successive time interval at 3 board`s depths (1/10, 1/3 and 1/2 of thickness).MC was established gravimetrically. pH-value determination of solid wood water system by suspending wood dust into distilled water was used. The lowest used temperature and duration of drying procedure had not significant influence on wood pH. Wood acidification was confirmed at higher drying temperatures (30°C and 65°C), particularly with lower drying rates and prolongation of the procedure. Among all the factors, drying temperature had the greatest impact on the pH-value of wood.
Keywords: ash-wood, pH-value, drying, drying conditions
Published in DiRROS: 12.07.2017; Views: 4231; Downloads: 1874
.pdf Full text (279,40 KB)

4.
Influence of drying temperature on properties of wood surfaces
Milan Šernek, 2002, original scientific article

Abstract: This article deals with modifications of wood surface properties induced by different drying temperatures. The aim of the study was chemical and physical characterization of a wood surface concerning low and high temperature exposure. Additionally, the correlation between the chemical composition of a wood surface and its wetting capacity were investigated. X-ray photoelectron spectroscopy and contact angle measurements were conducted. Two wood species, yellow poplar (Liriodendron tulipifera) and southern pine (Pinus taeda) were studied. The results showed that the percentage of carbon increased with drying temperature, and consequently, the percentage of oxygen decreased. The samples exposed to high drying temperatures indicated a higher content of extractives on the wood surface. These samples exhibited the highest contact angle and the lowest wettability
Keywords: površina lesa, sušenje, kontaktni kot, rentgenska fotoelektronska spektroskopija, omočitev, ekstraktivne snovi, wood surface, drying, contact angle, XPS, wettability, extractives
Published in DiRROS: 12.07.2017; Views: 4515; Downloads: 1906
.pdf Full text (932,44 KB)

Search done in 0.1 sec.
Back to top