1. Ciklični preizkusi armiranobetonskih stebrovMiha Kramar, Matija Gams, Andrej Anžlin, Matjaž Dolšek, 2016, original scientific article Abstract: V članku so prikazane eksperimentalne preiskave potresne odpornosti armiranobetonskih stebrov, ki so bile opravljene na Zavodu za gradbeništvo Slovenije (ZAG) z namenom, da se določi vpliv negotovosti oz. razpršenosti materialnih karakteristik in izvedbe na potresni odziv stebrov. Da bi zajeli kar se da veliko virov negotovosti, smo naročili izdelavo 12 stebrov, ki so jih izdelala tri različna podjetja na podlagi istega načrta in nominalno enakih materialov. Poleg materialnih karakteristik smo analizirali vpliv preklopa vzdolžne armature na potresni odziv stebrov. Stebre smo preizkusili s ciklično horizontalno obtežbo, ki smo jo povečevali do porušitve. Raziskave so pokazale, da so med proizvajalci v resnici velike razlike, ki pa so opazne predvsem pri odzivu stebrov po doseženi največji nosilnosti. Največji vpliv na duktilnost ima izvedba armaturnega detajla stremen. Z raziskavo smo potrdili tudi nekatere že znane odvisnosti in opazili, da bi lahko bil pomemben parameter potresne odpornosti tudi lokacija prvega stremena nad temeljem.
Keywords: armiranobetonski steber, potresni odziv, negotovosti, nosilnost, duktilnost, stremenska armatura
Published in DiRROS: 08.01.2025; Views: 843; Downloads: 399
 Full text (1,50 MB)
This document has many files! More... |
2. Experimental investigation of the axial strength of glued-in rods in cross laminated timberBoris Azinović, Erik Serrano, Miha Kramar, Tomaž Pazlar, 2018, original scientific article Abstract: This paper presents results from an experimental assessment of glued-in rods in cross laminated timber (CLT). For the purposes of the study more than 60 pull-pull tests were performed, where the specimens varied in terms of bonded-in length (from 80 to 400 mm), rod diameter (16-24 mm) and rod-to-grain angle (parallel and perpendicular). Several different failure modes that are not common for other applications of glued-in rods (e.g., a failure between CLT layers) were obtained for the analysed CLT specimens. It was found that these failure mechanisms can substantially influence the obtained ultimate tension loads. At the end, the experimental results were compared with empirical and semi-empirical equations for estimating the pull-out strength of glued-in rods in structural timber and glulam. The comparison showed that most of the existing equations overestimate the ultimate tension loads for specimens with the rod parallel to the grain and underestimate the ultimate tension load for specimens with the rod perpendicular to the grain. The results vary because the possible CLT failure modes were not included in previous studies. Further studies are proposed to improve the equations for glued-in rods in CLT.
Keywords: glued-in rods, cross laminated timber (CLT), pull-pull experiment, glued-in length, rod-to-grain angle, failure mechanisms in CLT
Published in DiRROS: 29.11.2023; Views: 1349; Downloads: 1071
Full text (4,13 MB)
This document has many files! More... |
3. Glued-in rods in cross laminated timber - numerical simulations and parametric studiesBoris Azinović, Henrik Danielsson, Erik Serrano, Miha Kramar, 2019, original scientific article Abstract: Numerical simulations and parametric studies of glued-in rods in cross-laminated timber have been performed. The simulations were based on 3D finite element analysis, using a cohesive surface model for the bond-lines between the laminations and the bond-line along the rod. The parametric studies investigated the influence of the glued-in length, the rod diameter, and the rod-to-grain angle on the load-bearing capacity and stiffness of the connection. The analyses showed that the load-bearing capacity generally increases with the glued-in length and the rod diameter, which agrees well with experiments. For different rod-to-grain angles, different mechanical behaviour was observed, especially considering the failure modes.
Keywords: glued-in rods, cross laminated timber (CLT), parametric study, nonlinear numerical modelling, glued-in length, rod diameter, rod orientation
Published in DiRROS: 13.09.2023; Views: 1637; Downloads: 830
Full text (2,66 MB)
This document has many files! More... |
